|
|
 |
 |
|
|
|
|
|
| WATER IONIZERS PTV-KL;PTV-K | | | | | | | | 1. GENERAL PROVISIONS | | | 1.1. Water ionizers PTV-KL (with timer), PTV-K - a devices in which ionized or silvered water is produced during water electrolysis. 1.2. Ionized water - alkaline and acid - is obtained in separate containers of water ionizer.
1.3. Alkaline water - has a weak negative electrical charge and has alkaline features.
1.4. Acid water - has a weak positive electrical charge and has acidic features..
1.5. Partition - wood fibre plate (plates) dividing the container into two parts, transmitting ions, but not allowing mixing of water.
1.6. Silvered water - water having silver ions concentration of which is measured in milligrams per liter (mg/l).
1.7. The device meets electrical safety and safety requirements.
| | | | 2. TECHNICAL CHARAKTERISTICS | | | Modification KL (device with timer), modification K (device without timer). Their technical characteristics are provided in the table: | | | | Parameters | Parameters value | | Vessel capacity, l | 1.4 | | Power supply voltage, V~ | 230 | | AC frequency, Hz | 50 | | Average duration of electrolysis when generating: | | | - ionized water, min | 25 | | - silvered water, sec. | 2-3 | | Silver electrode mass (assay 999,9), g | >9,7+/-0,1> | | Average power consumption when generating: | | | - ionized water, W | 100 | | - silvered water, W | 3 | | Appliance total weight KL/K, not exceeding, kg | 1.3/1 | | Naudojimo sąlygos:> | | | Water temperature | 10 to 25oC | | Safety class (water penetration) | IPX 1 | | Dimensions, mm | 190 x 160 x 200 | | | | | 3. DESIGN AND PRINCIPLE OPERATION | | | | 3.1. The device PTV-KL consists of a lower container (1), a removable vessel (3) and an enclosure (9). (See picture 1) 3.2. The lower container (1) is an electrolysis container. In the upper part of it two handles are installed. (2) A removable semi round vessel is built in the container (3), in which wood fibre partitions are set instead of the front wall (4). Partitions are fastened in the top with a fixer (5). On the inner side of the container and the vessel there are two marks: lower (6) indicates minimum and upper (7) - maximum water level. 3.3. In the enclosure (9) an electrical scheme is installed that is covered from inside with a plastic cover. In the cover flat electrodes (8;19) and round contact (18) are fixed. Flat electrodes are meant for production of ionized water and round contact- for connection of silver electrode. On the board (12) located on the top of the enclosure three LEDs are mounted: the middle, green (14), lights when the plug of the device (13) is connected to the power supply socket. The external, red (11;15) ones, light respectively when ionized or silvered water is produced. As well on the top of the enclosure four buttons for control of timer and working mode and time indicators are mounted (16). On the other side of the enclosure there is a cord with a plug. (13). The device control scheme does not allow to switch on the modes of production of ionized and silvered water at one time. | | |  | | Picture 1. General View of the Device PTV-KL | | |  | Picture 2. General View of the Device PTV-K | | | | 3.4. Partitions (4) are mounted into special notches of the removable vessel (3) (modifications KL and AL) and fastened with a fixer (5). 3.5. During water electrolysis acid water is generated at the black electrode (8) and alkaline water - at the light one (19). Partitions (4) of the removable vessel (3) do not allow acid and alkaline waters to mix. 3.6. When producing silvered water (modification KL) the removable vessel (3) is not necessary. | | | | 4. PROPERTIES OF IONIZED WATER AND ITS APPLICATION | | | 3.4. Partitions (4) are mounted into special notches of the removable vessel (3) (modifications KL and AL) and fastened with a fixer (5).
3.5. During water electrolysis acid is generated at the black electrode (8) and alkaline - at the light one (19). Partitions (4) of the removable vessel (3) do not allow acid and alkaline to mix.
3.6. When producing silvered water (modification KL) the removable vessel (3) is not necessary.
4. PROPERTIES OF IONIZED WATER AND ITS APPLICATION
4.1. Alkaline water, a natural stimulator, stimulates growth of plants, accelerates germination of seeds, flowering of domestic flowers, revives faded flowers, vegetables, etc.. It is a soft, odourless water having taste of rainwater.
4.2. Acid water, a natural bactericide, kills small pests, various microbes, bacteria, fungi. It is good in disinfecting soil, tare, fresh vegetables, fruit, etc.. It is a sourish water having typical acid and weak chlorine odour.
4.3. Alkaline and acid waters should be kept in tightly closed jars protecting them from direct sunlight. It not recommended to keep them in refrigerator. Alkaline preserves its properties for up to 3 days and acid - for up to 7 days.
4.4. Properties of ionized water are characterized by two indexes: ORP- oxidation- reduction potential and pH. ORP is characterized by positive or negative charges (mV) that respectively acid and alkaline charges. pH values can fluctuate between 0 to 14 units. Potable water is neutral, its pH is about 7,0. pH of alkaline fluctuates from 8,0 to 11,0 pH (the bigger this number, the more alkaline water is) and of pH of acid is from 6 to 2,4 pH (the smaller this number, the more acidic water is).
4.5. In the 1st table dependence of pH and ORP values on the working duration of the device is presented. These pH and ORP values have been obtained during testing of water used by the company- producer. In case of different composition of water values can differ. A minor difference of pH(+/-0,2-0,3) and ORP values does constitute practical influence.
| | 1 The table | | | | Duration of work | ACID | ALKALINE | | (electrolysis) of device | pH | ORP | pH | ORP | | (min) | (mv) | (mv) | | 5 | 6,12 | +48 | 8,74 | -103 | | 10 | 5,57 | +79 | 9,41 | -141 | | 15 | 3,72 | +185 | 9,83 | -165 | | 20 | 2,79 | +239 | 10,29 | -192 | | 25 | 2,54 | +252 | 10,33 | -194 | | 30 | 2,49 | +256 | 10,33 | -194 | | 35 | 2,41 | +261 | 10,33 | -195 | | 40 | 2,36 | +264 | 10,35 | -195 | | | | | 5. PROPERTIES OF SILVERED WATER AND ITS APPLICATION | | | | 5.1. Silver ions contained in Silvered water (their concentration is measured in mg/l) kills microbes, bacteria. Besides small silver doses positively affect organism. Constantly drinking silvered water concentration of silver ions should not exceed 0,01 mg/l (UN 48- 1994). Such concentration is obtained switching on the device for 2 seconds. 5.2. Impact of silvered water depends on concentration of silver ions: the bigger this concentration, the stronger the impact. In the 2nd table silver ions dependence on the working duration of the device is presented. 5.3. Silvered water preserves its bactericidal properties for several months. 5.4. For production of silvered water potable water is used. It is recommended to use filtered, spring water, or tap water that has settled. 5.5. Silvered water of low concentration is entirely clear, tasteless and odourless it has to be kept in dark premises. When boiling silvered water silver sediments precipitate and it loses its properties. | | 2 The table | | | | Working duration of device | Concentration of silver ions in water mg/l | | 2 sec. | 0,010 | | 5 sec. | 0,027 | | 10 sec. | 0,056 | | 15 sec. | 0,082 | | 30 sec. | 0,170 | | 1 min.. | 0,339 | | 5 min. | 1,671 | | 10 min. | 3,315 | | 15 min. | 5,022 | | 20 min. | 6,613 | | 30 min. | 9,95 | | 40 min. | 13,27 | | | | | |
|
| | | 6. PRODUCTION OF IONIZED WATER PTV-KL;PTV-K: 6.1. Holding the lower container (1) on its handles (2) remove the enclosure (9) of the device. 6.2. Make sure the partitions of the removable vessel (4) are tightly inserted into the notches of the vessel. 6.3. Pour cold water from tap: first of all into the removable vessel (3) then into the lower vessel (1) up to the lower marks (6). PTV-KL (See picture 1): 6.4. Put the enclosure (9) on the lower container (1) so that the dark electrode (8) would get into the removable vessel.(3). 6.5. Connect the cord with the plug (13) to the socket. On the enclosure (9) green indicator (14) lights up and in the indicator of timer (16) - letter A shows.. Set the working duration of the device according to the table 1. 6.6. Pushing the control button (16) indicated by arrow ↑ to set the required time of electrolysis. To reduce the set time push the button (16) indicated by the arrow ↓. Attention! Working time of the device up to 1 minute is set in seconds and from 1 to 40 minutes – in minutes. 6.7. Push the button START. Red indicator (15) lights up indicated by letter A. The device starts working. After the set time passes the device switches off automatically. To make a premature cancellation of the work of the device push the button STOP. After the work of the device is finished (when the time of switching on is longer than 3 minutes) a sound signal is given. It is switched off by pushing the button STOP. 6.8. Pull the plug of the cord (13) from a socket, take off the enclosure (9), pour out from the removable vessel (3) the acid and then alkaline into prepared, tightly closed jars. PTV-K (See picture 1): 6.9. Connect the cord with the plug (13) to the socket. On the enclosure (9) green indicator (14) lights up. Turn on the switch (16). Green (14) and red A (15) indicators must light. Set the working duration of the device according to the chart 1. 6.10. After the set time passes, turn off the switch (16),p ull the plug of the cord (13) from a socket, take off the enclosure (9), pour out from the removable vessel (3) the acid and then from the container (1) alkaline into prepared, tightly closed jars. PTV-KL; PTV-K 6.11. Just produced catholyte is turbid and sometimes foamy. After pouring catholyte into a jar, sediments and foam precipitate on the bottom, water becomes clear and suitable for using (the amount of sediments precipitated shows the level of contamination of water). 6.12. Just produced anolyte has a slight acidic and chlorine odour and is sourish. 6.13. When working with the device water can heat up to 40 degrees. 6.14. Wash the removable vessel (3) and lower container (1) with water. It is PROHIBITED to wash with water the enclosure (9) containing the electric part! 6.15. Clean the light electrode (19) and the contact (18) with soft cloth dipped in vinegar. It is not necessary to clean the dark electrode (8). 6.16. Dry the lower container (1), the enclosure (9) and removable vessel (3) without taking out the partitions. After the partitions (4) fully dry assemble the device and store it in dry place. | | | | | | 7. PRODUCTION OF SILVERED WATER | | | | PTV-KL; PTV-K: 7.1. Holding the lower container (1) on its handles (2) remove the enclosure (9) of the device. 7.2. Put the holder with the round silver electrode (17) on the contact (18) located on the enclosure (9) 7.3. Take out the removable vessel (3). 7.4. Pour water into the lower container (1) up to the lower mark (6). 7.5. Put the enclosure (9) on the lower container(1). PTV-KL (See picture 1): 7.6. Connect the plug of the cord (13) to the electricity supply socket. Green indicator (14) on the enclosure must light and letter J must appear in the timer indicator (16). From the table 2 choose duration of working time of the device. 7.7. Pushing time indicator button (16) indicated by arrow ↑ to set the time of electrolysis. To reduce the set time push the button (16) indicated by the arrow ↓. . 7.8. Push the button START. Red indicator (11) lights up indicated by letter J. The device starts working. After the set time pasess the device switches off automatically. To make a premature cancellation of the work of the device push the button STOP. 7.9. Connect the plug of the cord (13) to the electricity supply socket and turn on the switch (16). Green indicator (14) and red J indicator (11) on the enclosure must light. From the chart 2 choose duration of working time of the device. PTV-K (See picture 2): 7.10. Connect the plug of the cord (13) to the electricity supply socket and turn on the switch (16). Green indicator (14) and red J indicator (11) on the enclosure must light. From the chart 2 choose duration of working time of the device. 7.11. After the set time passes, turn off the switch (16), pull the plug of the cord (13) from a socket, take off the enclosure (9), pour out the silvered water into the jar that has to be stored in a dark room. PTV-KL; PTV-K: 7.12. Carefully clean the silver electrode (17) and the light flat electrode (19) with a soft cloth dipped in vinegar. Dark varnishes occurring on the silver electrode do not influence the quality of silvered water. 7.13. Dry the lower container (1) and the enclosure (9). Assemble the device and store it in dry place. 7.14. When producing silvered water for a longer time period dark spots occur on the bottom of the lower container (1). It is a residual effect of silver sediments. These spots do not influence the quality of silvered and activated water and further exploitation of the device. It is PROHIBITED to wash with water the enclosure (9) containing the electric part! | | | |
|
|
|
|
|
|
|
|
|
 |
|
 |
|
|
|
